TOP > ミュージック > batteryclub2019道場 > ネタ

道場TOP ネタ一覧 batteryclub2019道場

HP ProDesk 600G3 sff 901765-0034+4 PC psu replacement power service DPS-180AB-26 A

◇評価 0ポイント
◇閲覧回数 5,076
◇登録日
2019年9月24日
batteryclub2019
batteryclub2019
道場主

Lv.24

Check

前のネタへ
次のネタへ

Maximum transmission power supply replacement - HP DPS-180AB-26_A pc power supply +12.1V==14.88A 180W. DPS-180AB-26_A power supplies are compatible with HP ProDesk 600G3 sff 901765-0034+4. Shopping DPS-180AB-26_A pc power online, more discount and money-saving. Check your HP output power and voltage(Ref 80Plus) before you order DPS-180AB-26_A pc PSU service. Cost-effective computer power supply charging replacement, please visit www.batteryclub.org for more information.

HPQ17128_Se
  • Brand : HP power supply
  • Input Voltage : 100-240V ~,50-60Hz,2.3A
  • Ouput Volatge : +12.1V==14.88A 180W
    Is there no power supply model you find? Take it easy! Contact us fast with your e-mail for what PC power models your are looking for.

    Email: info@batteryclub.org

DPS-180AB-26_A replacement model:

DPS-180AB-26A 901765-003 901761-003 DPS-180AB-3A

Compatiblet with HP ProDesk 600G3 sff 901765-0034+4:

FOR HP ProDesk 600G3 sff
PN number:901765-003 901761-003
Interface:2 4 pins,1 flat 7 pin


How to maintain HP DPS-180AB-26_A computer power supply

1. Remove the fan. Disconnect the main power supply first, and unplug the input and output cables on the back of the power supply. Next, unplug and connect all the accessories connected to the power supply, remove the fixing screws of the power supply box, and take out the power supply box. Observe the appearance of the power supply box, remove the screws reasonably and accurately, and remove the cover. When taking the cover, the wires should be pulled out according to the gap at the same time. Remove the four screws that secure the fan and remove the fan. You can not solder the two power cables temporarily.
2. Clean the dust. After separating the power supply board and the fan with cardboard, use a small brush or a damp cloth to wipe the dust and wipe it clean. It is also possible to use dust from the fan to blow fan blades and bearings.
3. Add lubricant. Peel off the sticker and use a needle-nose pliers to pick out the rubber seal. Find the motor bearing, add lubricant, and when you use the fan to move the fan, make the lubricant flow evenly along the bearing, then add a few drops. Pay attention to whether the fan of the ball bearing has two bearings. Don't neglect the oil feeding to the bearing on the wind side. The oil can't be placed on the main shaft only. Lubricating oils must use computer-specific lubricants or advanced lightweight sewing machine oils. Never use the lubricants used in automobiles. Finally, install the rubber sealing sheet and label it.

Here, we provide other products for your reference:

HBC BA225030 2100MAH 6V battery

HBC BA225030 1500mah 6V battery

HBC QD109300 24V ac adapter

HP PCG007 310W power supply

Microsoft G3HTA001H 8030mAh/60.8Wh battery

Lenovo 45N1110 battery 24Wh 11.1V/11.4V

Huawei HB512627ECW battery 410MAH 3.82V

Lenovo L15D1P31 battery 4000mAh 3.8V

Huawei HB442528EBC battery 300MAH 3.8V

CRAFTSMAN CMCB6050 500mah/60V battery

Acer AS16B5J 5600mAh battery

Toshiba PA5173U-1BRS 5200mAh battery

Fujitsu FMVNBP212 2200mAh battery

other products

Dell HCWV2 100-240V ~/ 4.6A, 50-60Hz

Dell 6MVJH

LENOVO 54Y8861 100-240V``47--63HZ

DELL H275P-01 100-127V~/6A +5V==/18A, +3.3V==/5A

Dell H290AM-00 50Hz-60Hz

FSP FSP300-60PFN 115-230V 10/5A

HP HP-D3201E0 100-240 V-/5.5A , 50-60 HZ

FSP FSP270-60LE

【このネタに対するあなたの評価は?】
☆☆☆☆☆ ☆☆☆ ☆
【キーワード】

ブログ? そんなの必要ありません! 今日から、いきなりアフィリエイトスタート!

【まにあ道アフィリエイト】まにあ道ならAmazonアソシエイトIDを利用してネタを書くだけで、お気軽に始めていただけます。

新着クイズ

もっと見る

新着掲示板

もっと見る